Mamp;S Systems Stereo System MC111M DM User Manual

CONGRATULATIONS!  
Your purchase of an M&S Systems music and communications system is an investment that will provide years of enjoyment and service  
for your customer.  
M&S audio products are backed with more than 40 years of experience in the design and manufacture of precision acoustical equipment  
for the home. To ensure that your customer receives the high-quality music and voice reproduction that the system is designed to deliver,  
it is important that each step of the installation be done carefully. If you follow the step-by-step illustrated instructions below, the result will  
be a successful professional quality installation. In the event you need troubleshooting assistance, please call our technical staff at 1-800-366-  
9422.  
INSTALLATION INSTRUCTIONS  
FINISH-OUT MC111M/DM SYSTEM  
Toolsrequired:Phillipsscrewdriver#2,Standardatscrewdriver#1,  
wire stripper/cutter.  
REMOTE DOOR RELEASE STATIONS  
N15D/N35D SERIES  
The nish-out installation should be made after the application of wall  
covering material.  
At each door release control  
station  
location,  
strip  
approximately 4 inches of  
jacket (MS4XSC) from wires  
&
DOs  
DONT's  
and  
separate  
colored  
conductorsfromoneanother.  
Strip 1/2 inch of insulation  
fromeachconductorincluding  
theVM127X.Cutoffthedrain  
wire from the Black/White  
pair. Connect the Red wire  
from the volume control  
switch to the Red wire on the  
VM127X. Connect the White  
wire from the volume control  
to the White wire on the VM127X.  
USE ONLY M&S SYSTEMS BRAND CABLE as  
called out in these instructions. The cable is designed and  
constructed with electrical specications necessary for proper  
audio performance. IMPORTANT: THE USE OF NON M&S  
SYSTEMS’ BRAND CABLE OR CABLE SUBSTITUTION WILL  
VOID PRODUCT WARRANTY. Note: All M&S Systems’ cable  
has M&S Systems and the part number printed on it!  
DO NOT power up master until all remote stations and  
Figure 4  
speakers are connected.  
DO ensure that all rough-in instructions (literature number  
115741) have been followed before power is applied to  
system.  
SATELLITE VOLUME CONTROL  
MVC1 SERIES  
DO NOT SPLICE CABLES. Splices are unreliable and  
defeat the signal isolation properties of the cable.  
DO NOT COIL OR BUNDLE the MS4X cable. This will  
At each satellite control station  
location, strip approximately 4  
inches of jacket (MS4XSC and  
MS2SXSC) from wires and  
separate colored conductors from  
one another. Strip 1/2 inch of  
insulation from each conductor.  
Connect drain wires together  
frombothcablesusingawirenut  
(MS4XSC only). Wire nut each  
colored conductor to its  
cause electronic feedback.  
If extra cables have been run for possible future speaker  
additions, care must be taken that these cables do not get  
connected to the master unit. Unterminated cables (no  
station) connected to the master unit may cause electronic  
feedback that will damage the master unit.  
DO NOT overtighten the screws for the remote stations or  
the master as the plastic face panels may crack or strip out.  
Figure 5  
REMOTE STATIONS N14/N35 SERIES  
respective wire as shown in gure 5. Connect Blue and Violet wires  
to the corresponding terminals of the satellite speaker(s). Mount  
the volume control to the single gang box using the two screws  
provided with the volume control.  
At each remote station location,  
strip approximately 4 inches of jacket  
(MS4XSC) from wire and separate  
the colored conductors from one  
another. Strip 1/2 inch of insulation  
PATIO STATIONS NW14/NW35 SERIES  
from  
each  
as  
Figure 1  
conductor  
At each remote station  
l o c a t i o n , s t r i p  
approximately 4 inches  
ofjacket(MS4XSC)from  
wire and separate  
colored conductors from  
one another. Strip 1/2  
inch of insulation from  
each conductor. Cut  
eachshielddrainwireat  
theshieldfoiltoprevent  
shown in gure  
1. Cut each  
shield drain wire  
at the shield foil  
to prevent them  
from  
each  
touching  
other  
(MS4XSC only).  
Connect each  
c o l o r e d  
conductor to its  
Figure 2  
Figure 3  
themfromtouchingeach  
other (MS4XSC only).  
Connect each colored conductor together using wire nuts as shown  
in gure 6. Mount the patio station to housing using the two screws  
provided with the station.  
respective screw terminal as shown in gure 2. Mount each remote  
station to it’s mounting ring using the two screws provided with each  
station as shown in gure 3.  
Figure 6  
 

Life Fitness Home Gym Club Series 45X User Manual
Lightolier Landscape Lighting LR Series User Manual
Linksys Network Card HPN200 User Manual
Lux Products Thermostat PSPLV512 User Manual
Magic Chef Microwave Oven MCD990STG User Manual
Makita Cordless Saw XSH01X User Manual
Maytag Washer W10420493A User Manual
Melissa Microwave Oven 653 115 User Manual
Mellerware Hot Beverage Maker 22550 User Manual
Middleby Cooking Systems Group Oven PS870 Series User Manual